SRD-6VDC- 10A 250VAC 5PIN RELAY – KSH 70 at HIMASTORES Mombasa – best electronics in Kenya
Home / Relays / SRD-6VDC- 10A 250VAC 5PIN RELAY

SRD-6VDC- 10A 250VAC 5PIN RELAY

SKU: HMJ598 Category: Relays
KSH 70.00
Out of Stock

Product Description

SRD6VDC 10A 250VAC 5Pin Power Relay

Low-Voltage SPDT Relay for 6V Systems

The SRD6VDC is a 10A power relay with 250VAC switching, featuring a 6VDC coil and 5pin SPDT configuration. This relay enables control of highpower loads from lowvoltage logic circuits.

Low 6V Coil - Directly compatible with 5V logic systems
High Load Capacity - 10A at 250VAC for industrial applications
Requires stable 6VDC supply at 167mA coil current
Use socket for easy field replacement
Never exceed 10A contact current rating

Technical Specifications

ParameterValue
Coil Voltage6VDC
Coil Resistance36Ω (±10%)
Coil Current167mA
Contact FormSPDT (5-pin)
Contact Rating (AC)10A at 250VAC
Contact Rating (DC)10A at 30VDC
Max Switching Power2500VA / 300W
Operate Time10ms max
Release Time5ms max
Mechanical Life10 million ops
Electrical Life100,000 ops

= Pin Configuration =

Pin NumberFunctionConnection
Pin 1Coil (+)6VDC positive
Pin 2Coil (-)6VDC ground
Pin 3CommonLoad common
Pin 4Normally OpenClosed when energized
Pin 5Normally ClosedClosed when de-energized

= Key Features =

5V Logic Friendly - Works with 5V microcontrollers with adequate drive

HeavyDuty Contacts Handles 10A loads reliably

Low Coil Power - Only 1W consumption

Fast Response - 10ms operate time

Standard Form Factor Industrystandard pinout

= Applications =

  1. 5V Arduino and Raspberry Pi projects
  2. Battery-powered devices
  3. Portable equipment control
  4. Small appliance switching
  5. Model railroad controls
  6. Prototyping circuits
Perfect for Makers - Directly interfaces with 5V logic
Established Design - Millions in use worldwide

√ Ready for breadboard and PCB use

√ Compatible with logic-level MOSFET drivers

√ UL recognized and TUV approved

Driving Recommendations

Coil drive options:

  • Use transistor (2N2222 or BC547) for logic control
  • Use MOSFET for low-power dissipation
  • Provide 1.5x coil current for reliable pickup
  • Include diode for back-EMF protection
Use 1N4007 diode across coil in reverse bias
Add 100µF capacitor near relay for stable pickup

Protection Requirements

Surge Protection - Diode across coil mandatory

Contact Protection - RC network for AC, diode for DC

Overcurrent - 10A fuse on load side

Temperature Operate 25°C to +70°C

Always use transistor driver - never connect directly to microcontroller pins
Use flyback diode on inductive loads to prevent contact damage
Maintain minimum 3mm creepage distance on PCB

Troubleshooting

No pickup:

  • Check 6VDC under load
  • Verify transistor saturation
  • Avoid long wires with high resistance

Contact failure:

  • Reduce switching frequency
  • Add arc suppression
  • Avoid capacitive loads without precharge-
99% production yield rate
Direct factory support available

Ordering Options

Part NumberCoilContactsPackage
SRD-6VDC6V10ASingle
SRD6VDC106V10A10-Pack
SRD6VDCT6V10ATube (20)

Wholesale Pricing for volume orders

Ships Same Day on all orders

√ Fully tested before shipment

√ 2-Year manufacturer warranty

√ Complete datasheet included

Arduino5V CompatibleBest Seller